About LayIt and its methods
LayIt is a set of free layout and quantity calculators. This page lists the formula behind each one, separates what is exact from what is a rule of thumb, and says where each one stops being trustworthy.
Who runs this site
LayIt is an independent site. It is not owned by, paid by or affiliated with any tile maker, mortar maker or retailer, and no product is placed on a page for payment. The site may carry clearly labelled advertising, and links to retailers are marked when they are affiliate links; the privacy page says exactly what the current build loads. Quantities are never adjusted to sell more of anything: each formula is printed so you can check it by hand.
How the tools work
Every tool runs entirely in your browser. There is no account and no server-side processing, and nothing you enter is transmitted or stored. Internally every calculation is done in millimetres and square metres; imperial input is converted on the way in and every result is shown in both systems. The conversion factors are exact by definition: 1 inch = 25.4 mm, 1 foot = 304.8 mm, 1 pound = 0.45359237 kg.
Rounding happens once, at the end: exact quantities are computed, the waste allowance is applied, and only then is the result rounded up to whole tiles, boxes, boards or bags.
Exact arithmetic
These tools involve no assumptions beyond the numbers you enter:
- Square footage — rectangles (length × width), triangles (½ × base × height), half circles (π × d² ÷ 8) and quarter circles (π × r² ÷ 4), added and subtracted. Exact for the shapes entered; approximate only in how well those shapes match the room.
- Tile layout — tiles repeat every tile + joint; the tool places that grid three ways (full tile at a wall, joint on the centre line, tile on the centre line) and measures the edge piece each leaves inside the span minus the perimeter gap. The ratings (half a tile or more is good, under a third is a sliver) are an installers' rule of thumb, labelled as such.
- Page grid — content = width − 2 × margin; column =
(content − (columns − 1) × gutter) ÷ columns. This matches how CSS
column-gapworks.
Arithmetic with a rule of thumb on top
Tile quantities
The floor and wall tile calculators divide the area by (tile length + joint) × (tile width + joint), which is exact, then add a waste allowance, which is not. The default allowances are:
- Straight (grid): 10% (commonly quoted range 5–10%)
- Offset (brick, 1/3 or 1/2): 10% (commonly quoted range 10%)
- Diagonal (45°): 15% (commonly quoted range 15%)
- Herringbone or chevron: 20% (commonly quoted range 15–25%)
These are the figures tile retailers and installers commonly give. They are not measured for any particular room, and small or complicated rooms use more. Every waste figure is editable.
Grout
The grout calculator uses the formula printed on tile-product manufacturers' coverage charts: litres per m² = (L + W) ÷ (L × W) × joint width × joint depth, all in millimetres. That volume is geometry and is exact for square-edged tiles. Converting it to weight needs a density, and published figures for cement grouts vary; the default is 1.8 kg/L and the page always shows the result at 1.5 and 1.9 kg/L as well. A manufacturer's own coverage chart for the product you buy is better than any generic figure.
Plank flooring
The flooring calculator divides area plus waste by the coverage printed on the box. Its row plan subtracts the expansion gap from each wall, divides by the plank's face width, and reports the leftover as the last row. The "narrow" warning at under a third of a plank is a working threshold chosen for this site, not a published standard; flooring makers set their own minimums, and theirs apply.
Pavers, base and sand
The paver calculator's paver count is exact arithmetic plus a waste allowance. The base is the paved area extended by an overhang on every side, times the compacted depth, plus an editable allowance for compaction (default 20%). Bedding sand gets a fixed 10% allowance. Weights use a density range of 1.5 to 1.8 tonnes per cubic metre, because the true figure depends on the stone, its grading and its moisture; a supplier's own conversion should override it. The suggested base depths (4 to 6 in for foot traffic, 8 to 12 in for vehicles) are commonly cited industry ranges, and soil, drainage and frost change them.
Decking
The deck calculator counts rows as ⌈(width + gap) ÷ (board + gap)⌉, joists as ⌈length ÷ spacing⌉ + 1, and screws as rows × joists × screws per crossing. Board counts are shown two ways, one row at a time and with offcuts reused, because the real number depends on how the boards are cut. It is a materials count and nothing more: it does not size joists, beams, posts or footings, which are governed by building codes.
The tile project planner
The tile project planner reuses the tile and grout methods above for every surface, and adds coverage rates published by product makers for the rest of the job:
- Thinset with a 1/4 × 1/4 in square notch (6 × 6 mm): 75 to 100 sq ft per 50 lb bag, planned from the low end.
- Thinset with a 1/4 × 3/8 in square notch (6 × 10 mm): 55 to 67 sq ft per 50 lb bag, planned from the low end.
- Thinset with a 1/2 × 1/2 in square notch (12 × 12 mm): 42 to 47 sq ft per 50 lb bag, planned from the low end.
- Large-format tile (an edge of 15 in or more) gets 15% more mortar for back-buttering: a working allowance, not a published rate.
- Grout gets 10% for mixing and clean-up, as LATICRETE's coverage chart advises.
- Liquid waterproofing: 55 sq ft per gallon for two coats (CUSTOM RedGard). Sheet membrane: 54 sq ft rolls plus 10% for overlaps.
- Backer board: 3 × 5 ft or 1200 × 800 mm sheets plus 10% for cuts, on floors over wood and on wet walls only.
- Spacers (about two per tile), levelling clips (about three per large tile) and trim (2.5 m lengths plus 10%) are rules of thumb and say so.
Sources
- CUSTOM Building Products, VersaBond Professional TDS-119 (thinset coverage by trowel)
- MAPEI, Ultraflex 2 technical data sheet (thinset coverage by trowel)
- CUSTOM Building Products, RedGard TDS-104 (55 sq ft per gallon as a waterproof membrane)
- LATICRETE grout coverage chart (add 10% for waste and clean-up)
- Schluter-Systems, KERDI roll sizes and profile lengths
- Tile waste allowances: the ranges tile retailers and installers publish; treated as rules of thumb.
- Unit conversions: the international yard and pound agreement of 1959 (1 in = 25.4 mm exactly).
What none of the tools know
Whether your walls are square, whether your tiles match their nominal size, how many you will break, what your soil is like, or what your local building code requires. Measure the real thing, read the manufacturer's instructions, and treat every result here as a well-founded estimate to check against them.
Not professional advice
Everything on this site is general information for estimating materials. It is not engineering, structural or installation advice. Decks, driveways and anything load-bearing or attached to a building should follow local codes, and may need a permit and a qualified professional.
Corrections
If something here is wrong, please say so. The formulas are stated on each page and above so they can be checked.